Knowledge Base

A:  The recommended charging current is 0.5C, or 0.5 times the battery capacity. The recommended discharging current is 0.25C, or 0.25C times the battery capacity. Here are some settings for common batteries:

2700mAh Charge: 1300mA Discharge: 700mA

2650mAh Charge: 1300mA Discharge: 700mA

2500mAh Charge: 1200mA Discharge: 600mA

2300mAh Charge: 1100mA Discharge: 600mA

2200mAh Charge: 1100mA Discharge: 600mA

2100mAh Charge: 1000mA Discharge: 500mA

2000mAh Charge: 1000mA Discharge: 500mA

1000mAh Charge: 500mA Discharge: 200mA

900mAh Charge: 400mA Discharge: 200mA

850mAh Charge: 400mA Discharge: 200mA

A:  Yes! The charger defaults to CHARGING mode at 1A if no button is pressed 10 seconds after inserting the batteries. This is the default auto charging mode and does not require you to program the charger.

A:  When tested using the REFRESH/ANALYZE mode, the capacity will be lower than the capacity on indicated on the battery. To obtain a capacity that is closest to the rated capacity, use the BREAK-IN mode, which is similar to the process used by manufacturers to test and rate the batteries.

Furthermore, most batteries have a typical and minimum capacity. The Powerex 2700mAh batteries, for instance, has a 2700mAh typical capacity and a 2500mAh minimum capacity. Therefore, a Powerex 2700mAh that tests to be higher than 2500mAh using the BREAK-IN mode is considered within specification.

A:  Simply round up to the next capacity. For 2650 mAh battery, use 2700mAh capacity.

A:  Upon completing the charge, the MH-C9000 goes to a very slow charge current (less than 10 mA) to keep the battery topped off. This "trickle charge" stops only when the batteries are removed. It is okay to keep the batteries in the charger as the batteries will always be ready for use. However, exercise common sense when keeping appliances constantly plugged in the wall.

A:  When using the BREAK-IN mode, the charger puts in 1.6 times the capacity of the battery (entered at the start of the charge). This does not cause any harm to the battery as the charging rate is very low (only 10% of the battery capacity). The increased total charging capacity compensates for energy lost as heat. This is the charging scheme recommended by International Electrotechnical Commission (IEC).

A:  The charger terminates by voltage and by temperature simultaneously. For certain older (and low quality) batteries, they do not produce the proper negative delta V signal (a small voltage drop at the conclusion of the charge) needed for the charger to stop. At the same time, the battery temperature failed to reach the termination limit as the charging rate was probably too low.To address this issue, you should attempt to perform a BREAK-IN mode on the batteries first. You should also use a higher charging rate.

A:  The charger terminates by voltage and by temperature simultaneously. For certain older (and low quality) batteries, they do not produce the proper negative delta V signal (a small voltage drop at the conclusion of the charge) needed for the charger to stop. At the same time, the battery temperature failed to reach the termination limit as the charging rate was probably too low.To address this issue, you should attempt to perform a BREAK-IN mode on the batteries first. You should also use a higher charging rate.

A:  When charging at higher current, the charge completeness reduces thereby lowering the charging capacity. This is to prevent battery overheating. This typically occurs at a rate greater than 1500mA. Generally speaking, 1000mA achieves nearly full charge completeness for AA batteries.Even after the charge ends (DONE appears on screen), the charger will apply a topoff charge and continuous maintenance charge. Despite that the capacity on the screen no longer increases, the batteries are being topped off.If you would like to achieve better charge completeness at higher currents, a small fan can be added to cool the batteries externally.

A:  When charging below 0.33C (except in BREAK-IN) mode, the batteries may not produce a sufficient end-of-charge signal for the charger to terminate correctly. Although the temperature sensors will safeguard battery overheating, lower charging rate might not cause enough heating in the batteries to trip the sensors.If low charging rate is desired, you should use the BREAK-IN mode. Charging in that mode is terminated by only time (1.6 times battery capacity) and temperature.

A:  In the first few seconds, the MH-C9000 performs a proprietary “high impedance” check to filter out batteries unsafe to charge including non-rechargeable batteries. During this time, a high current is applied and voltage measured to determine the impedance of the battery.

A:  The charging and discharging current are pulsed, thereby causing the displayed current to go up and down. The capacity calculation is based on the actual current rather than the set current so capacity calculation remains accurate.

A:  The capacity displayed in any charging process is called the “charging capacity.” This is the amount of energy put into the batteries. This number does not equal to the battery’s capacity as it is dependent on the amount of charge already in the battery as well as the battery’s internal resistance.For example, a half used 2000mAh battery may only show a charging capacity of 1000mAh since the battery is half full.It is normal for the charging capacity to exceed battery capacity by as much as 30% depending on battery brand and charging rate.To determine the battery’s useful capacity, you must look at a “discharge capacity.” Such information is available in the REFRESH & ANALYZE, BREAK-IN, DISCHARGE, and CYCLE modes. Note that the battery is not recharged in the DISCHARGE mode.

If charging or discharging is in-progress, a blackbox contain either CHARGE or DISCHG will be displayed on the screen. The capacity shown during charging is always the charging capacity. Similarly, the capacity shown during discharging is the discharging capacity.In the CHARGE mode, the final capacity displayed (after DONE appears) is the charging capacity.In the REFRESH & ANALYZE and BREAK-IN mode, the final capacity displayed is the discharging capacity. The battery have also been recharged after the discharge.In the DISCHARGE mode, the final capacity displayed is also the discharging capacity. However, the battery is not recharged.In the CYLCE mode, the capacities saved in memory always refer to the discharging capacity.

A:  The LCD screen displays information a slot at a time. The information (capacity, current, time, voltage) is displayed twice before moving on to the next slot. The arrow points to the slot reporting.

A:  Yes, batteries do get warm during the charge due to both internal heat and heat produced by the charger. Lower charging rate can yield lower battery temperature, but it is not recommended to go below 0.33C or 0.33 times the battery capacity. Adding an external fan can also cool the battery.

A:  Most NiMH batteries can accept discharge rate up to 3 times its capacity. A higher discharge rate will yield lower capacity.For accurate capacity measurement, use the BREAK-IN mode which complies with IEC standards (0.2C discharge rate).

A:  Yes, follow the same charging rate recommendations for general NiMH batteries.

A:  The maximum capacity supported (BREAK-IN mode) is 20,000mAh making it compatible with future technologies.

A:  Virtually all batteries can be detected by the charger. Therefore, if a battery cannot be detected, it is likely not making good contact with the charger. This can be caused by improper seating of the battery or battery not meeting the IEC dimension standard. Try rotating the battery or placing it in another slot.

A:  The charger can produce some high frequency hum, which is generated by the high frequency pulse charging and switchers.

A:  The charger takes several minutes to detect whether or not a battery is fully charged. It is normal for the charger to put in a small amount of charge to fully charged batteries. Your unit may be faulty. Please contact Maha Energy's support team for warranty services.

 

A:  No. The charging current displayed on the screen does not include a brief rest period (a fraction of a second every two seconds). Therefore, the actual charging current is about 90% of the displayed value. Discharging prior to BREAK-IN mode is optional. Overcharging during the BREAK-IN mode does not harm battery as the charging current is very slow.

A:  The MH-C9000 features a high impedance tester which can screen for defective/damaged battery. Most consumer chargers on the market does not have this feature, and therefore will allow charging batteries not may no longer be suitable for use. Maha recommends that batteries triggering a "HIGH" error be disposed for safety reasons, as charging damaged batteries may result in overheating or explosions.However, if you feel the HIGH error is due to a false detection, try charging the battery first in another charger, or drain the battery first using the DISCHARGE mode on the MH-C9000. This is recommended only for advanced users.

A:  The MH-C9000 uses a combination of Negative Delta V, Zero Delta V, Peak Voltage, time and temperature to determine the end-of-charge. In addition, proprietary algorithms are used.